referral_links

gallery_videos

phone_override

Aggregate Systems Inc

2016 Portable Hopper with Stationary 80' ConveyorInventory #: CV2578

New/ Never Used Conveyer and Hopper

2016 MODEL HOPPER AND CONVEYOR NEW NEVER BEEN USED. HAS AR 400 LINERS ON SLOPES ON HOPPER HOPPER 10' WIDE X 17'8" LONG 42" CONVEYOR UNDER HOPPER SINGLE AXLE

42" X 80 FT CONV HAS THE FOLLOWING DODGE 9 : 1 RATIO 30 HP 1800 RP 480/240 V

HOPPER CONV HAS THE FOLLOWING DODGE 15 : 1 RATIO 40 HP 1800 RP 480/240 V

STATIONARY- 80' X 42" TRUSS FRAME DISCHARGE CONVEYOR (2-40'SECTIONS)

2016 2016 2016 HOPPER AND CONVEYOR Conveyors EQUIPMENT

NEW 40' Lab/Control House/Office SpaceInventory #: CON2686

Size: 40' Climate-controlled space with heating and air conditioning. Dual entrance doors. Spacious open room with the option to add a divider wall for flexible use.

Also Listed as LAB2685

NEW LAB/CONTROL HOUSE/OFFICE Stationary Aggregate Equipment EQUIPMENT

Natco CO-600 BoilerInventory #: HT2623

Make: SN: JNB 6727 Max Water Temp: 5331 Safety Valve Rel. Cap: 500 Year: 2007 Repaired 11/17/2023 by Ashley Mechanical Inc. Power Flame Natural Gas/Fuel Oil Burner

Condition Notes: Has leak that will need to be welded. Used until April 2024. Was set up as a steam boiler for hot water for a concrete plant.

2007 NATCO Boiler Aggregate Equipment EQUIPMENT

Portable 2-Bin Cold Feed System (Blending Hopper) Inventory #: CF2630 Portable 2 Bin Blending Hopper complete as follows: Used only for a few buckets to calibrate belting.

a.  Each hopper is 9’-6” wide x 14’ long with 20 tons storage capacity constructed from 1/4” thick steel plate with rectangle tube reinforcing at the hopper top and angle iron reinforcing at the hopper mid-section and bottom section; self-relieving tapered hopper bottom opening to minimize bridging; full length skirtboards with Hercules 3/4" x 6" adjustable rubber flashing to prevent leakage between hopper bottom and belt feeder; adjustable discharge gate with hand crank to control material flow from each hopper.

 b. Each belt feeder is 30” wide x 8’ long with Nord 5 h.p. gearmotor drive; 12” diameter rubber lagged head pulley mounted on Dodge 2-7/16” SCM pillow block bearings; 12” diameter self-cleaning tail pulley mounted on Dodge 2-3/16” SCM pillow block bearings; screw take-up assemblies; ICC CEMA “C” flat belt idlers with 5” diameter rolls mounted on close centers; 3 ply vulcanized endless conveyor belting. Belt speed setup for 90 fpm.

 c. Collecting conveyor is 36” wide with Nord 10 h.p. gearmotor drive; 12” diameter rubber lagged head pulley mounted on Dodge 2-3/16” SCM pillow block bearings; 12” diameter self-cleaning tail pulley mounted on Dodge 2-3/16” pillow block bearings; screw take-up assemblies; head pulley nip guards; ICC CEMA “C” 35 degree troughing idlers with 5” diameter rolls; ICC CEMA “C” return idlers with 5” diameter rolls; 2 ply conveyor belting with 3/16” x 1/16” rubber covers; Flexco 140 mechanical belt splice; 9’-6” long conveyor extension beyond the hoppers which folds for transport.

 d. Portable trailer constructed of heavy duty wide flange beams which are braced for optimum rigidity; wide flange vertical beams and angle iron cross members tie all hoppers and trailer together; single axle chassis with dual 11 x 22.5 tires, air brakes, king pin, rear lighting, mud flaps and blocking pads. Includes one set of hand crank landing legs at the king pin.

 e. One rust inhibitor prime coat and one finish coat gray paint for all equipment; one finish coat safety yellow paint for all guarding.

 f. Electric motor control panel with main disconnect, AC Tech SMV variable speed drives for the belt feeders, branch circuit protection, fixed speed starter for the collecting conveyor, all mounted on a skid support structure bolted to the trailer frame and wired into the electric motors. All motors and electrical controls are 3 phase/460 volts/60 hertz.

 Excludes bulkheads, liners, belt scrapers, grizzlies, bin extensions, bin vibrators, air cannons, flow switches, safety stop switch with pull cords, belt scales, return idler guards, PLC, permits, freight to jobsite, jobsite preparation or equipment installation.

2024 Rock Systems 108-2P Aggregate Equipment EQUIPMENT

NEW BURNER CONTROL PANELInventory #: BC1810

NEW BURNER CONTROLS MADE TO ORDER- CALL TODAY FOR THE QUOTE 1- Burner control will come with the following. ( stack and mix temp control, all safety wiring, Additional wiring or controls to operate a phoenix burner

2023 OTHER EQUIPMENT BURNER CONTROLS Asphalt Plant Components EQUIPMENT

NEW Digital Amp GuageInventory #: CON1819

Built to your specific plant needs

Digital amp gauges with audible and visual alarm for over amp conditions on motors, typically drag chain,drum, traverse

Installation is an additional cost

Manufacture Time 4-6 Weeks

2023 UKNOWN Digital Amp Gage Asphalt Plant Components EQUIPMENT

STAINLESS STEEL 25TPH, NEW Stainless Steel Salt Dryer Inventory #: DR1200 Capacity: 25t/hr Length/Width: 250‘‘ x 74‘‘ Three Phase: 230/440v Amps: 50/30 BTU‘s: 4,600,000 Gas Pressure: 10-15psi Gas Consumption: 40 gal/hr Other: Shut Off High Temp Continuous Flow High quality parts and construction, Dependable and Reliable Economical and Efficient, Superior Workmanship 12 month warranty on parts 12 To 14 Week manufacture time NOTE: Picture is of a NEW dryer. May or May Not be the dryer described above. CALL FOR PRICES

STAINLESS STEEL 25TPH Asphalt Dryer Units EQUIPMENT

12mbtu PX120 HeaterInventory #: HT1958

PX120 Heater This heater is rated for up to 125 PSI @ 650 deg f. The heater will net out 12.0 MMBtu/Hr. Manufacture time approx 14 weeks.

Heater 12MBTU PX120 Asphalt Plant Components EQUIPMENT

AC TANK 20,000 GALLON, NEW Vertical 20,000 Gallon Electric Tank Quote Inventory #: ACT1592 Vertical Asphalt Tank Heat source: Electrically heated Size: 20,000 Gallons Specs: constructed of 1/4" plate and will have Electric 52kw elements in bottom of tank Standard features: 18" Manway on top 24" Diameter manway on bottom for clean out Caged ladder on top Bolt on handrail around top with toe plate Gauge board level indicator Tank thermometer in drywell 4" Vent and overflow line 3" Fill line with valve 3" Supply line with valve 3" Return line with valve 6" Fiberglass insulation on top 3" on bottom 6" Fiberglass unsulation on sidewalls Aluminum jacket covering .032 thickness Tank is equipped with high and low limit switches to deviate hot oil when tank is empty and also sound an alarm or cut off asphalt unloading pump when tank is full Tank is completely prewired to bottom of tank Tank is equipped with an alarm on mixer motor, if overloads trip an alarm will sound Sampling valve 15-30k GALLON TANKS AVAILABLE- HORIZONTAL OR VERTICAL! Other Info: The Mixer will be right angle euro drive helical bevel speed reducer flange mounted. 45rpm mixer with 10hp motor. Tank will be equipped with 3 sidewall baffles to prevent certrifige effect on mixing Photos are of recently made tanks that are similar 6-8 weeks lead time (may vary) Also available is piping/ insulation installation to incorporate tank into your project. 40+ years with tanks and Heatec references Terms: 40% down payment 60% due @ shipment

 

AVAILABLE UNTIL OCTOBER 2023

AC TANK 20,000 GALLON Tanks EQUIPMENT

WEBSTER BURNER, NEW - 20MBTU Webster Burner Inventory #: BN1198 Make: Model: Output: 20MBTU/hr ( has 8-1 turn down ratio) Fuel: Vaporous LP Gas Other: 10hp Siemens Gas Train Size: 3" Supply Voltage: 460V/60Hz Control Voltage: 120V/60Hz/1 Control Transformer: 0.5 KVA Flame Safeguard: Honeywell Blower Motor: TEFC 460V/60Hz/60Hz/3 Configuration: Upright Panel Location: Remote Wall Mount Junction Box Location: Top *Picture not actual burner, but a similar burner that company manufactures. New orders will take additional time to assemble and prepare. Current production time is 6 weeks.

WEBSTER BURNER Aggregate Equipment EQUIPMENT

1 each - Portable 4 Bin Blending Hopper complete as follows:

a.  Each hopper is 9’-6” wide x 14’ long with 20 tons storage capacity constructed from 1/4” thick steel plate with rectangle tube reinforcing at the hopper top and angle iron reinforcing at the hopper mid-section and bottom section; self-relieving tapered hopper bottom opening to minimize bridging; full length skirtboards with Hercules 3/4" x 6" adjustable rubber flashing to prevent leakage between hopper bottom and belt feeder; adjustable discharge gate with hand crank to control material flow from each hopper.

b. Each belt feeder is 30” wide x 8’ long with 5 h.p. electric motor and Nord helical bevel right angle gearbox; 12” diameter rubber lagged head pulley mounted on Dodge 2-7/16” SCM pillow block bearings; 12” diameter self-cleaning tail pulley mounted on Dodge 2-3/16” SCM pillow block bearings; screw take-up assemblies; CEMA “C” flat belt idlers with 5” diameter rolls mounted on close centers; 3 ply vulcanized endless conveyor belting. Belt speed setup for 90 fpm.

c.  Collecting conveyor is 36” wide with 15 h.p. electric motor and Nord helical bevel right angle gearbox; 16” diameter rubber lagged head pulley mounted on Dodge 2-15/16” SCM pillow block bearings; 14” diameter self-cleaning tail pulley mounted on Dodge 2-7/16” SCM pillow block bearings; screw take-up assemblies; tail terminal guard; head pulley nip guards; CEMA “C” 35 degree troughing idlers with 5” diameter rolls; CEMA “C” return idlers with 5” diameter rolls; 2 ply conveyor belting with 3/16” x 1/16” rubber covers; Flexco 140 mechanical belt splice; 9’-6” long conveyor extension beyond the hoppers. Belt speed setup for 350 fpm.

d.  Portable trailer constructed of heavy duty wide flange beams which are braced for optimum rigidity; wide flange vertical beams and square tube cross members tie all hoppers and trailer together; tandem axle chassis with dual 11 x 22.5 tires, air brakes, king pin, rear lighting, mud flaps and blocking pads. Includes one set of hand crank landing legs at the king pin.

e.  One rust inhibitor prime coat and one finish coat gray paint for all equipment; one finish coat safety yellow paint for all guarding.

f.  Electric motor control panel with main disconnect, AC Tech SMV variable speed drives for each belt feeder, fixed speed starter for 15 h.p. collecting conveyor motor, circuit breaker branch circuit protection, control power transformer, start/stop push buttons for each motor, speed potentiometer for each belt feeder, emergency stop button, selector switch for each belt feeder to run only the desired belt feeders for special blends, all mounted in a NEMA 4 enclosure; includes wiring from each electric motor to the control panel; skid mounted support structure bolted to trailer frame.

CONTACT ASI FOR COST AND LEAD TIME

CF BIN 4 BIN COLD FEED Aggregate Equipment EQUIPMENT

CF BIN 5 BIN COLD FEED, NEW Stationary 5 Bin Cold Feed (9‘6"x14‘) with Control Panel Inventory #: CF0938 12-14 weeks 1 each - Stationary 5 Bin Cold Feed Hopper complete as follows: See ASIEQUIPMENTSALES.COM for more Info

CF BIN 5 BIN COLD FEED Aggregate Equipment EQUIPMENT

COLD FEED BIN SINGLE BIN COLD FEED, NEW Portable 3 Bin Cold Feed (9‘6"x14‘) - 8wk Wait Inventory #: CF0632 1 each - Portable 3 Bin Blending Hopper/Cold Feed System, Model 108-3P complete as follows:

COLD FEED BIN SINGLE BIN COLD FEED Aggregate Equipment EQUIPMENT

CF BIN 2 BIN COLD FEED, NEW Portable 2 Bin Cold Feed (9‘6"x14‘) Inventory #: CF0287 1 each - Portable 2 Bin Blending Hopper, Model 108-2P complete as follows: See ASIEQUIPMENTSALES.COM for More Info

CF BIN 2 BIN COLD FEED Aggregate Equipment EQUIPMENT

COLD FEED BIN SINGLE BIN, NEW Portable Loading Hopper with Feeder (14‘6") Inventory #: CF0892 1 each - NEW Front End Loader Hopper with Belt Feeder, Model 101-36 complete as follows: See ASIEQUIPMENTSALES.COM for more info

COLD FEED BIN SINGLE BIN Aggregate Equipment EQUIPMENT

AC TANK NEW QUOTES, NEW AC TANKS! Inventory #: ACT1708 NEW AC Tank Quotes! Any sizing up to 30,000 gallon Vertical or Horizontal Electrical/Coiled. Aggitation This supplier has been making tanks for 40+ years! The photos are of our most recent project: (2) 30,000 Gallon AC Tanks for Nebraska

 

AVAILABLE UNTIL OCTOBER 2023

AC TANK NEW QUOTES Tanks EQUIPMENT

AC TANK 10,000 GALLON, NEW Skid Mounted 10,000 Gallon A.C. Tank Inventory #: ACT1082 Make: N/A (New AC Tank) Size: 40,000 Liter, approx. 10,000 Gallons Portability: Designed to Fit into Shipping Container Interior: Inside Steel is ASTM A36 or Equivalent Heating Indirect "Coiled" Other Info: Outside is Colored Steel Sheet and Material is A36 or Equivalent Insulation Layer is 50mm (2") of Rock Wool Material Between Inside Steel and Outside Steel Cover All of Piping is ASTM grade Steel Boiler Tube or Equivalent Floating Level Gauge at One Side of the Wall Leaking Test on Hot Oil Heating Tubes Inside of the Tank One Ladder Outside and omne Ladder Inside Included Approx. 10-14 week delivery time

Aggregate Systems Inc

Filtro de búsqueda

Refinar busqueda

Tipo

Distancia

Tipo de Listado

Categoría

Fabricar

Modelo

Precio

Condición

Horas

Año

País

Estado

Ciudad

Clase

2016 2016 2016 HOPPER AND CONVEYOR

NEW LAB/CONTROL HOUSE/OFFICE Stationary

2007 NATCO Boiler

2024 Rock Systems 108-2P

2023 OTHER EQUIPMENT BURNER CONTROLS

2023 UKNOWN Digital Amp Gage

STAINLESS STEEL 25TPH

Heater 12MBTU PX120

AC TANK 20,000 GALLON

WEBSTER BURNER

CF BIN 4 BIN COLD FEED

CF BIN 5 BIN COLD FEED

COLD FEED BIN SINGLE BIN COLD FEED

CF BIN 2 BIN COLD FEED

COLD FEED BIN SINGLE BIN

AC TANK NEW QUOTES

AC TANK 10,000 GALLON